[Manufacturer part number] Q3PPIA045618 [PIAA part number] MLE6
[Set components] ・Valve 1pc ・Controller x 1
[Specification] ・Type: H4 ・Compared to stock halogen candela: 230% compared to stock ・Light: 6000K ・Brightness: High 1400 lumens / Low 1000 lumens ・12V 24 / 24W LED ・Double-sided board approx. 0.9mm ・Specially designed for motorcycles 20G
・High performance control circuit
*There are some models that cannot be installed, so please check the application chart to see if your vehicle can be installed. *Please use the same power consumption as the original bulb. *Vibration-resistant valves are specially designed for bikes and are not designed to withstand electrical shocks caused by voltage changes. *Brightness sense is an image of visibility due to color rendering property and bulb characteristics, not luminous flux or illuminance. *The color temperature (K=Kelvin) is a unit of color light, and the higher the number, the dimmer the light.It has nothing to do with the temperature or brightness of the light source.
* The image is only for reference. The image shown may differ from the actual product.
230% brighter than stock! Equipped with an ultra-thin 0.9mm base!So bright!The latest Candela-oriented model! 230% brighter than stock!
New technology to irradiate lumens to the road surface without loss! It is a product that focuses on the essence of irradiating the road surface without loss of lumens (lm / total luminous flux), and thoroughly pursues the reproduction of stock light distribution with the essential performance of Candela.
■Bright candela value The 0.9mm ultra-thin substrate achieves a candela value of 230% of the halogen value. This product LED 28500cd Stock halogen 2160cd This is the reference value measured by XSR700 / 900 Low Beam.The candela value may vary depending on the luminaire.
■High level of vibration resistance and water resistance It has an overwhelming seismic resistance that has cleared 20G.The water resistance is high, and the water resistance when mounted on the headlight clears the water resistance standard JIS S2.
■High performance control circuit It supports the lighting operation range from 9V to momentary maximum 24V, and it is also compatible with vehicles with unstable idling peculiar to motorcycles!
■Power consumption cut by 56%! Eco-friendly performance that can be lit with only about 24W.(General halogen lamp 55W)
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
Recently viewed products
Ratings & reviews for this product or related products
After 5 years of use, the low side of the LED headlight stopped working, so I decided to buy a new headlight. I chose the "PIAA PIAA MLE6 6000Kelvin 12V−24/24W" from a number of potential LED headlights. I was a little worried because there was no room in the headlightReverse side of GSX-S1000. The wiring is long, but if you wrap it around, it will fit beautifully. The instructions are very detailed and easy to read, and I can work with ease. The brightness is needless to say. Other companies show Lumen&Kelvin, but PIAA also shows Candela, which I liked. I chose this one from the sense of security of the car inspection, durability, and others though there is a cheap thing if "explosion light" is desired.View Detail
It is brighter than the NORMAL Headlight Bulb. Because I think that it is a place where I am glad to have corresponded to the vehicle inspection and the vibration countermeasure is done tightly because it is two-wheel for vehicle, I expect the long life.View Detail
Installation is a simple matter of reading the instruction manual, it shouldn't be too difficult. There was a fan on the back and it seemed to hit the fan lightly, so I used a Light caseRearHole saw to make a hole in it. Wiring of the Controller felt long, but in fact, if it is a cowl car, it will be long, and if it is a non-cowl car, it will be short. My RC42 has a depression under the rear end of the tank. There is a Large Kinky Coupler in the generator, but I managed to fit it. Wiring of Controller is the feeling that there is a little room cutting Handlebar. When I tried to ride at night after installing it, there was no problem, but when I rode on the next day, the Light went out when I set the High beam switch to Low. The Indicator is working. So, when I checked, it connects Coupler of Light valve and Coupler of Controller, but even if it inserts firmly, the inserted part floats. There may be the affinity with the coupler of the vehicle, but if the above-mentioned symptoms occur, please see the coupler. Or if you insert the Coupler in advance, please tie it up with Tie Wrap to prevent it from falling out. At first, I had no idea what was going on, and I was worried about it.View Detail
I installed it on my Ninja250SL and if you're looking for an LED Headlight Bulb is highly recommended It's nice to see a reliable manufacturer's product, and that's the PIAA As the product claims, the luminous point is quite close to the OEM Halogen bulb, and the light diffusion The way it works is almost the same as OEM It is often said that LED Bulb cannot use high beam, but this Valve It is very similar to the OEM, even the way the high beam is illuminated They do However, if you turn it around and don't like the way the OEM illuminates it, you can't expect to replace it It also means that there will be none The light is crisp and clear and it looks like an LED I used to use a cheap LED Bulb, but this one is not so bad was subtle But with this Valve, it shines brightly and is very cool There is enough light itself The availability of the OEM WaterproofRubber is also a high point However, you may need to modify it depending on the model of car But I managed to get it without any processing I attached the pedestal to the rubber cover and put it on the back of the body, because the pedestal and the body are separated It is a form to fit the Body into the base There are two L-shaped slits in the inside of the pedestal, and the two projections of the Body are pushed in there and twisted to fix the Body It's not hard to see why, as the Construction Manual explains in detail I guess It's also nice that the cooling is a fan, but it makes very little noise You won't hear it first By the way, the Controller is also included, although it is not in the image Wiring is very long In general, I can highly recommend Valve It has the performance to match the high priceView Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!