7.33 EUR
(1,200 JPY)
6.63~ EUR
(1,086 JPY)
(10% OFF)
4 (8 Reviews)
Very Good
Thanks for preparing OEM's SizeOEM Roller of WR250F has decayed, so exchanging, Bearing Smooth movements in internal organs. I'm glad that Color will also be One Point. Although I purchased M and L, it was slightly different. It was attached without problems.
Reviews For DRC Chain Roller From Other Webike User
Excellent
Mounting on KLX 250I installed it in KLX 250.
With OEM Roller and Black,
I thought that I wanted a color at some point and purchased it.
I can not see much if I install it - - - (;^^)
Because it is just replacing with OEM's Roller,
Installation is very easy.View Detail
Excellent
Used for YZ250FSince Roller on the lower side of YZ250F was decreasing, I chose L Size.
Bearing is also solid, rotation also Smooth.
It was cheaper than OEM Product.View Detail
Excellent
Chain roller self-madeAlong with extension of Rear suspension of XL 1200 C SPORTSTER 1200, I made Bracket and attached Chain Tensioner Roller to suppress slack at the lower side of Drive chain.
If there is nothing there is no problem, there is no problem, but if there is, the time lag of the slack of Chain which started running will decrease, the Throttle response will be felt well and the bash crash when throttle is closed will also decrease, so that it will be hard to make a shit is.View Detail
Poor
KLX125 is a little Large.So I
NSK (NSK) Stainless Steel MINI Auteua BearingZZ Flange type Model SMF
Insert inside with SMF128ZZ
Use OEM by turning without Flange
Color of inner diameter 8 mm is required.
Washer etc. on the outside of Bearing as well
Devices are designed so that rotation becomes Smooth
Until 11 years the year is 14 / 8
However, since 12 years the outer diameter is 12.
Bolt size is 8 mm.View Detail
Most Viewed Reviews Of DRC Chain Roller
Excellent
Looks durableInstalled on XL125R, size S. When I went for OffRoad course, the NORMAL chain roller cracked after one run and flew away and was lost. Every time I run, the chain roller of NORMAL breaks somewhere. Bear Ring Type seems to be more durable, so it was EXACTLY for Repair.View Detail
Excellent
No problem with OEM ratio.I installed it on FZ750 modified (FZr1000Swing Arm).
There is no difference in quality compared to OEM.
It is very smooth because of the built-in ball bearing.
I drove about 2000km after installation, but there is no noticeable decrease, and durability seems to be no problem.
Even though it has Bearing built in, it would be nice if it was cheaper.
There are several sizes available, so you can choose the right size for your car model.View Detail
Average
It needed some processingIt's a standard KLX125, but the KLX150BF is also equipped with one that doesn't turn as well, so we delivered it I replaced it during maintenance
I don't know if it's the individual difference, but as it is, the diameter of LINK has a larger diameter than OEM It seemed to interfere with the mountings, so I used Cutters to remove some of the parts
Other than that, it's not particularly good or badView Detail
Excellent
CorocoroNORMAL did not rotate, it got worn and replaced.
I think that resistance is also decreasing a little by rotating, but I do not feel it in particular.
Color (color) You can also choose, so the Dress - up effect is half the Large - - - ?View Detail
Average
Just fitSher rattles are somewhat concerned. Okay ~ Rumor is one piece decrease phenomenon?
Try to remove it, Big! It was rotating pretty.
How to exchange.
Engineer Tsuduaku from day to day, may have been rotating as it attached Grease to the moving section. Individual difference?
First, Glasses on Reverse side (Prevents Nut from tampering as it is from the Reverse side) , The table is a long patterned Wrench (Torque up) , * STAND a cushioning material such as Dustcloth (Described later)
Because I could not insert it to the end at the Bolt, as soon as I got to Screw Mountain tighten together.
The impression is the Brush - Bo effect? ??Surely the sounds that Bearing is running are done. It is not bad.
If the color is Red or Blue, so dirt becomes more conspicuous, so change it to black color.
By the way, winding Dustcloth on Side Stand is because you can give power without hesitation. If you are not nervous, feel free.View Detail
Other Reviews From Japan User(translated)
Excellent
Radipon handled in Mild?attachment
The CBR650R is mounted at the same position angle as the NORMAL.
However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away.
I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose.
・NORMAL (Reserve integrated horizontal master) Impressions of
No complaints on public roads. Familiar feel and very easy to handle.
However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful.
Radipon (Reserve separate body portrait master) Impressions of
It was totally different from what I expected, my expectation was that it would feel like a Rear brake…
It is really a mild and easy-to-handle radipon.
On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN?
But I felt the radipon effect from Breaking a little stronger, and
It can be hung up to a hard brake without effort.
I felt trust that this could stop.View Detail
Very Good
packtalk bold Attached MountI purchased this for use with multiple Helmets. 。
Mount included with the BOLD.
Microphone and speaker are not included and must be purchased separately.View Detail
Excellent
Grip replacementGrip that had been used for a long time was worn out and had to be replaced.
They are soft and dampen vibration.View Detail
Very Good
Works well in everyday life[How is it used?
Used to lick Screw loose.
Was the one you received as per Image?
As per Image.
How was your experience with it?
When used on a strongly tightened Screw, it can be safely and securely removed.
The licked Screw was removed.
It is also useful for DIY Screw removal.
[Points to note]
When used on a licked Screw, it is best to beat it in with a Hammer before use.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING